Aged Bronze Flush Mount House Number 2, 6 in. Set! Gather supplies: mailbox numbers, (not included: tape, and ruler). Go time. Allow paint to dry. Slowly peel off the clear, front transfer film. Aged Bronze Screw On House Number 6. 2021 Modern House Numbers Keep vertical guidelines aligned. Unsubscribe at any time. With your number, letter, or plaque order,well include instructions, mounting hardware, and a handy drilling template. Peel off the number backing and align with tape guide. Clean and dry the mailbox surface. Aged Bronze Screw On House Number 5, 6 in. Peel off the front transfer film. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. Aged Bronze Screw On House Number 3, 4 in. With your order, you'll receive our custom-made modern house numbers/letters, threaded aluminum studs, 1/2 inch aluminum spacers (which give your numbers that "floating" look), pre-printed mounting template, and printed instructions on an easy step-by-step process for installing your modern house numbers. For horizontal arrangement, go to step 2A. Gather supplies: house numbers, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level). Instructional video of how to install your modern house numbers on a stucco wall. Matte Black Aluminum Floating or Flat Modern House Number 2, 6 in. Apply a thin layer of epoxy to the end of the exposed studs. No spacers were used. Apply even pressure along the entire surface. Matte Black Aluminum Floating or Flat Modern House Number 1, 6 in. Aged Bronze Screw On House Number 0, 6 in. Light tapping may be required. Push studs into pre-drilled holes on the back of the number. Carefully remove template. Ready? Rinse gently with clean, fresh water. Tape all edges. Align X marks on each template at top and bottom to achieve equal spacing between each number. Press stencil decal firmly with even pressure onto concrete at desired location. Skip to step 4. If so, place on a soft surface. Slide spacers over studs. Align templates vertically using labeled vertical guideline. The below Instructional video demonstrates how to install aluminum powder coated letters on an office wall. Installation Instructions Step 1 Tape the paper mounting template to the desired location and use a level to align template. Overlap of paper template edges is to be expected. Go time! Step 3 Slide spacers over studs and apply epoxy or clear siliconeto the end of the stud. Clean surface of all loose debris. Light tapping with a rubber mallet may be required. Arrange individual paper templates in desired order. CARING FOR YOUR PRODUCTS: To extend the effective life of your numbers, clean them every six months or every three months in coastal or industrial regions. Aged Bronze Screw On House Number 2, 6 in. Remove tape. Masonry, concrete, and stone installations may require a hammer drill. Gather supplies: plaque, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level). Push number into holes. Continue to Numbers Installation . For decals, it doesnt get any easier than peel-and-stick! Align templates horizontally using labeled guidelines at top and bottom. Tape template at desired location. Get exclusive access to new products and deals. Gather supplies: tape and ruler (not included). Keep guidelines straight, maintain your desired spacing. Note: Steel studs must be fully concealed to protect from the elements. Use a ruler to measure the space between each number. Press numbers firmly onto mailbox. Place a piece of tape to align the bottom edge of the numbers. Use a level to align template. Drill holes according to marks on the template - use 3/16" drill bit. All Rights Reserved. CARING FOR YOUR PRODUCTS: To extend the effective life of your plaque, clean every six months or every three months in coastal or industrial regions. Use clear tape to connect individual templates together. Dry with non-abrasive towel. Take care not to scratch the face of the plaque. Light tapping may be required. Local store prices may vary from those displayed. Need Help? Peel off number backing. Take care to not scratch the face of the plaque. Determine your desired spacing between numbers on the available space. Push plaque into holes. Spray paint stencil using multiple, light coats. Ready? Masonry, concrete, and stone installations may require a hammer drill. Please note that these letters are mounted flush on the wall. This is your drilling guide. well include instructions, mounting hardware, and a handy drilling template. Step 4 Push number into the mounting holes. Aged Bronze Screw On House Number 4, 6 in. Proudly Made in USA. Adequately protect adjacent surfaces with paper. Use of this site is subject to certain Terms Of Use. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. Note: decal should not be applied on rough surfaces or in wet, freezing conditions. Once dry, slowly remove stencil. Push studs into pre-drilled holes on the back of the plaque. Light tapping with a rubber mallet may be required. Rinse gently with clean, fresh water. Take care not to scratch the face of the number. For vertical arrangement, skip to step 3A. Use 11/64 drill bit or specialty 3/16 bit for masonry and rock. Aged Bronze Flush Mount House Number 1, 6 in. Dry with non-abrasive towel. For a worry-free install, get acquainted with our step-by-step installation instructions! Note: Curb stencil should not be applied in wet or freezing conditions. Overlap of paper template edges is to be expected. Aged Bronze Screw On House Number 1, 4 in. 2000-2022 Home Depot. Overlap of paper template edges is to be expected. Note: decals should not be applied on rough surfaces or in wet, freezing conditions. Set! Step 2 Screw in the threadedstuds into the back of the number. Note: Steel studs must be fully concealed to protect from the elements. Drill holes according to template. Measure the desired number location. Apply a thin layer of epoxy to one end of the stud. Please call us at: 1-800-HOME-DEPOT (1-800-466-3337), Please enter in your email address in the following format: you@domain.com. With your number, letter, or plaque order. Take care to not scratch the face of the number. Take care not to over spray. If so, place on a soft surface. Gather supplies - curb stencil decal, (not included: spray paint, paper roll and masking tape). For a worry-free install, get acquainted with our step-by-step installation instructions! Products shown as available are normally stocked but inventory levels cannot be guaranteed, For screen reader problems with this website, please call 1-800-430-3376 or text 38698 (standard carrier rates apply to texts), 6 in. For decals, it doesnt get any easier than peel-and-stick!